0%

0%

Jack Berendt

..

Following Follow me

Send a private message

Similar accounts worth following

Send a private message

This user joined on 04/10/2020.

My Projects

5-inch-screen Raspberry Pi Tablet.

Pi Tablet MK1

Projects I Like & Follow

Full-on Spotify scrolling and streaming via a Raspberry Pi Zero W and the original iPod clickwheel. Bluetooth, WiFi, and haptic feedback!!

sPot: Spotify in a 4th-gen iPod (2004)

guy-dupont Guy Dupont

Supplyframe DesignLab: 2022 Hackada…

Open up a 2010 iPad, remove its logic board, and fabricate a new board based around the Raspberry Pi CM4.

Put a Raspberry Pi CM4 into an original iPad

Medium-sized 12-DOF Quadruped Robot inspired by MIT Cheetah and Boston Dynamics Spot Mini

NOMAD Quadrupedal Robot

implemented-robotics Implemented Robotics

2021 Hackaday Prize

A jumperless breadboard

breadWare

kevin-santo-cappuccio Kevin Santo Cappuccio

What, you're using a 555? I could've done that with a microcontroller!

ATTiny555

shranav-palakurthi Shranav Palakurthi

Supplyframe DesignLab: 2022 Hackada…

Harvesting electricity with the help of moss dwelling microorganisms!

Moss Microbial Fuel Cell

MINI-ITX laptop with full desktop GPU, CPU motherboard and RAM, as well as custom watercooling.

Janktop IV Mini-ITX Laptop (4.1 Coming soon)

slightlylessstripeysnake

Not yet another esp32 watch :)

TshWatch, watch based on esp32

A Waveform analyzer, Signal generator and logic tester in a small PI PICO. With a dedicated application, Runs on Android.

Raspberry Pi Pico 200Khz Digital Oscilloscope

sagar-001 Sagar 001

2021 Hackaday Prize

This project uses a phased arrray of ultrasonic transducers to levitate and move a 1mm foam ball to draw in mid-air using the POV effect.

Volumetric Display using Acoustically Trapped Ball

dan-foisy Dan Foisy

A project initially based on Grant Searle's "CP/M on breadboard" and heavily inspired by RC2014

Baffa-2 Homebrew Microcomputer

augusto-baffa Augusto Baffa

I will present my early homemade computers around 1980 that was the starting point for the computer project I have already introduced.

Prehistory of my homemade PERSEUS computers

mitsuru-yamada Mitsuru Yamada

The Baffa-1 is an 8-bit CPU created from scratch using 74 series logic gates and built using custom printed circuit boards.

Baffa-1 Homebrew CPU Minicomputer

augusto-baffa Augusto Baffa

This CNC is based on GRBL0.9 Firmware and CNC V3 shield GRBL is Hacked for Z-axis Servo.

How to Make GRBL + CNC V3 Shield Based Mini CNC

on rpi GPIO is enough signals to direct button matrix + 2" IPS 320x240 display.

#Zepir CYBERDECK - Raspberry Pi Zero mini computer

Supplyframe DesignLab: 2022 Hackada…

Open up a 2010 iPad, remove its logic board, and fabricate a new board based around the Raspberry Pi CM4.

[HDP 2022] Put an RPi CM4 into an original iPad

The linear motor was a compact, ironless design with flat coils and magnets. It was intended for use in experimental haptic applications.

DIY Linear Motor Experiment

ANSI-compatible serial terminal built with Raspberry Pi Pico and EL640.480-AM/AG screen

ELterm

wenting-zhang Wenting Zhang

View all

Bits

Mitsuru Yamada wrote 04/22/2022 at 05:15

Thank you for liking and following my #Prehistory of my homemade PERSEUS computers !

Are you sure? yes | no

Dusan Petrovic wrote 01/26/2022 at 16:03

Hi @Jack Berendt - thank you for following my #Homebrew CPU list.

Are you sure? yes | no